Bailey Package

The Bailey Stall Package Includes:

• One SDSO Aluminum Sliding Stall Door Superstructure
  • Fully Welded Door Assembly
  • Bar Top with 1” Pickets and a 3” Between Bar Spacing on Top 4’0”
  • Load Lumber from Bottom (lumber not included)
  • Bottom Cap Channel 
  • Door Size is 4’3-1/2” Wide x 8’0” High
  • Your door opening needs to be: 4'0" Wide (or smaller) x 8'1-1/2" High (If you don't have this much height, please call us and we will accomodate your size!)
  • You will need a 7-1/2" header above the door opening to mount the door track. (If you don't have this much room, please call us and we will accomodate your situation!)
• Door Hardware
  • One 8’0” Galvanized Self Cleaning Round Track with fasteners for lumber installation
  • Two Neoprene Ball Bearing Trolleys
  • Two Aluminum Door Stops with fasteners for lumber installation
  • One Zinc Plated Slide Bolt Super Latch
  • One Heavy Duty Adjustable Wall Mount Stay Roller with fasteners for lumber installation
• One L Series Aluminum Stall Front Grill with Feeder Options Available
  • Fully Welded Grill Assembly
  • All welds are concealed for a clean, finished appearance!
  • Four Feeder Options Available (additional cost apply for the following 4 options)
    • The Feeder Access Door: The Hingeless, Latchless, "Built In" Feeder Access Door: Lift Up and Swing to Open, Lift Up and Lower to Close. The "built in" door is unnoticable at first glance and lends itself to giving your barn a continuous and uncluttered whole aisle appearance!
    • The Lift Out Panel: A completely removable section of grill, within the stall front grill, that allows your horse to hang it's head into the aisle. It can be used to feed through as well! The Lift Out Panel is ALSO unnoticable at first glance and lends itself to giving your barn a continuous and uncluttered whole aisle appearance! 
    • The Cut Out Feeder Access is an 11" x 11" opening in the stall front grill used to access horse feed bucket or bowl. 
    • The EZ Lift Feeder Access is the same 11" x 11" opening as the Cut Out Feeder Access but the EZ feature includes a "lift up, lower down" door for accessing the feeding container.
  • L4X Stall Grill assembled with 1-1/2” x 1-1/2” ANGLE on Top and Bottom Horizontals for mounting
  • 1” Diameter Round Pickets and a 3” Between Bar Spacing
  • Choose your grill width from the drop down menu when ordering. Various widths to choose from and if you don't see the size you need, please call or email us, we will accomodate your situation! 
  • Pre-Drilled with Fasteners for lumber installation 
  • No Lumber in Lower 4’0” of Stall Wall
• Two Aluminum Receiver Channels & Four Aluminum Header Channels
  • Four 7-1/2" Header Channels hold the header in place above the stall door and stall grille. Fasteners are included.
  • Two Receiver Channels: Receiver Channel are two individual channels that are NOT welded or connected to the stall grill, but are separately mounted, below where you intend to place the stall grille. Receiver Channels mount vertically to the stall end posts and, once affixed, horizontal 1-1/2" lumber can be inserted into the Receiver Channels to construct the stall's front wall. Fasteners are included.
• You will need to provide
  • Three 6" x 6" x 12'0" posts (One post at each stall end and one 4' over from one end. When you plan for multiple stalls, please remember, stalls that are side by side will share a common post!)
  • Nine 2" x 6" x 12' boards (to construct the stall front wall & fill the bottom of the stall door)
  • One 2" x 8" x 12' board (header)